We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.

Let us help you with your inquiries, brochures and pricing requirements

The iNET-600 Series A/D module provides 16SE/8DI voltage input channels (Ch#1...#16). Each of these channels can be independently programmed using Windows software which supports direct connection to many common sensor types. The voltage input range on each channel can be independently programmed using the software to one of the following: ±20 mV, ±40 mV, ±80 mV, ±150 mV, ±300 mV, ±600 mV, ±1.2 V, ±2.5 V, ±5 V, ±10 V.

A mating Hd44 female connector and cover are included. Alternatively, an iNET-600 series can be attached to the following optional wiring boxes: iNET-500, iNET-511, iNET-512. An iNET-510 wiring box should be used if work with thermocouples is required, as it provides internal cold junction compensation.

The iNET-600 Series is a stand-alone USB data acquisition system. No additional components, for example, an external power supply, are required. Included in the box are an iNET-600 Series hardware device, a USB Cable, a CD containing relevant software, a mating Hd44 female connector and a Hd44 Cover.

The maximum digitizing sample rate is 160 K sample/second for 1 channel, 12 K samples/sec/channel for 2 channels, 6 K samples/sec/channel for 4 channels, and 3 samples/sec/channel for 8 channels. For more details, see voltage accuracy.

For each channel, a range of parameters are programmable using the software. These parameters are the following: A/D signal-averaging-per-point (0 ... 100 mSec), sample rate (samples-per-second-per-channel), voltage measurement range (±20 mV to ±10 V), Digital IIR filter (low pass, band pass, high pass, or band stop), sensor type, and single-ended or differential wiring.

Excitation power is provided for sensors (+3.3 V ±0.2 V, < 80 mA, 28 mA per sensor max), as are other end user power voltages. Referenced to instruNet ground, this 3.3 V, is automatically read back by A/D during the calculation of sensor values.

The digital I/O port for the 4 mA sink/source is made up of 4 individual TTL compatible lines (Ch#25...#28), which can each be configured as either input or output bit. When configured as an input, a channel can be used to sense a digital low (0 V to 0.8 V) or a digital high (2 to 5.5 V). When configured as an output, a channel can be set low (e.g. < 0.8 V) or high (e.g. > 2 V). These I/O pins are short-circuit protected against high voltages greater than 6.0 V and down to -6.0 V.

The sensors can be set up easily using the Quick Setup dialog box.

Each of the iNET-510, iNET-511 andiNET-512 wiring boxes can be easily bolted to devices in the iNET-600 series. The iNET-510 is the cheapest and the simplest, and also offers thermocouple support.  The iNET-511 includes 8 BNC connectors, while the iNET-512 includes a vRef/2 source.  This source can be used to help complete ¼ bridge and ½ bridge strain gauge circuits. If thermocouple measurement is required, then the iNET-510 is the only wiring box that will work, as a result of its internal temperature sensor for cold junction compensation.

5-Point Traceable Calibration High Stable Wet/Dry Differential Pressure Transducers

Calibrate Your Temperature, Pressure and Other Process Control Devices at the Calibration Center

Calibrator for Thermocouple and RTDs

Constant Temperature Liquid Circulating Baths for Laboratory and Industrial Applications

Digital Pressure Gauge for Differential Pressures for High Accuracy

Displaying Temperature, Process, Rate and Time

Gas Analysis with the Mass Flowmeter

Infrared and Surface Calibrations with the Dry Block Temperature Calibrators

Measuring a Variety of DC Voltage and Current Outputs with the iS32 PID Controller

Measuring Clean Gases with Flowmeters

Measuring Conductive Liquids for Food and Wastewater Applications

Measuring Mass Flow Rate, Volume and Temperature with the FMC 5000 Coriolis Mass Flow Meter

Measuring Pressure and Temperature of Process Gases

Measuring Temperatures up to 200 °C with the Linear Strain Gauges

Monitoring Liquids and Energy with Ultrasonic Flowmeters

Portable Dry Block Calibrator for Field and Lab Work

Pressure Transducers for Industrial Applications

Reading Gas Mass Flow with the Gas Mass Flowmeters

The High Accuracy, Fast Sampling Platinum Digital Panel Meter Series for Temperature and Process Meters

AZoM.com - An AZoNetwork Site

Owned and operated by AZoNetwork, © 2000-2022